All he could tell me was to make sure everything was square.Thank you Mr. There was no spec sheet with them and I went to the seller. I measured every which way I could and it was not perfect but all three drawers (1 per cabinet), fit in all three cabinets so I knew I was close. 4 out of 10 would not engage the self closing mechanism. I had Accuride slides initially, self closing. Wish I had this info before I did the first set of cabinets. You are answering questions I wasn't sure how to ask. In contrast, when you're boring for shelf pins, it's 37mm in from the cabinet front, 37mm in from the inside of the back panel, and a line centered between the front and rear holes. You'll note, too, that the fixed part of the glides set back roughly 2mm from the front of the cabinet when you have the first line of holes at 37mm from the front edge of the cabinet. You'll note that most gaps between hole lines are 128mm EXCEPT between the second and third hole lines where it drops to 96mm. One example would be the Accuride glides that I use. Quote from: Sparktrician on March 03, 2020, 08:21 AM Remember to set the holes closest to the front at 37mm from the front edge of the cabinet sides, then space the second, third, etc., holes at predetermined gaps from the first hole as you progress toward the back of the cabinet, and all reference on the first hole at 37mm from the front. Sent from my SAMSUNG-SM-G890A using Tapatalk Once you get used to the setup of the LR32 its fast, easy, and near perfect. That way it doesnt matter if youre piece fits perfectly between the stops. I can make my boxes whatever size i want, just have to be sure to reference the LR32 end stops off the same end of a cabinet component when line boring front and back rows of holes. Set door on a spacer, screw on the plates, done. Id much rather bore all my doors the same, and use a simple jig to mount them, or use face frame style hinge plates and no jig at all. And the problem compounds when you have some doors hanging flush to the bottom of a cabinet, but others held up slightly, or sharing a horizontal partition, etc. Your boxes have to be a certain height and depth for it to work properly. But using it to mount doors and drawers is more trouble than its worth imo. The holes are clean and perfectly aligned. I initially went down the rabbit hole of trying to incorporate everything into the 32mm system (shelves, drawer glides, and hinge plates). Ive been using the LR32 with OF1010 for a couple years now. The rear row of holes is not as critical, but should be bored so that one of the rear holes in your slides will line up. Other manufacturer's hardware works with the same setback (Grass, Salice, etc.) Once you've chosen a base plate position, you simply drill the hinge cup in the door to match. The hinge base plates fit exactly into a pair of holes spaced 32mm and require the same 37mm set back. With holes bored at a 37mm set back, these slides can be placed at exactly the 3mm set back per the installation specs. The holes in the Tandem slides are machined to accept 5mm euro screws. I normally use Blum Tandem undermount drawer slides. This is a standard setback for euro hardware. I bore my front holes with a "set back" of 37 mm from the front edge of the carcass. The rail can also be used as a regular guide rail with Festool routers, saws and jigsaws.The beauty of the 32mm system is that once you've done your line boring, those holes can be used for shelf pins, drawer slides AND hinge base plates. The LR32 guide rail with positioning holes is purchased separately in 1400 (FE-496939) or 2424mm (FE-491622) lengths. PLEASE NOTE: The 8mm collet is required for cutters supplied with this kit. The rail can also be used as a regular guide rail with Festool routers, saws, and jigsaws. The LR 32 guide rail with positioning holes is purchased separately in 1400 mm or 2424 mm lengths. The set includes clamps, stops, cutters, and the guide plate that is fitted to the router.Īn 8 mm collet is required and is sold separately for the LR32 to work with the OF 1010 and the OF 1400. Compatible with OF 1010 and OF 1400 routers, as well as previous OF 9 models, the LR 32 easily creates 32mm spaced shelf pin holes for your furniture. Hole Drilling System Systainer Set for LR 32 Systemįestool's LR 32 adjustable shelving system allows quick and precise hole placement without time consuming measuring and marking.
0 Comments
Leave a Reply. |